A non-spinning Samsung washer may be frustrating, especially if you have moist clothes after a wash cycle. Your Samsung washer may not spin for several reasons, from a dirty filter to a broken motor. This essay will discuss common causes and provide solutions to repair your washers. If your Samsung front load washer, top load washer, or high-efficiency Samsung VRT Plus is not spinning, this tutorial will help you solve.

Possible Samsung Washer Not Spinning Causes

Many things might stop your Samsung washer from spinning as it should. The most often occurring causes will be discussed below together along with ways to spot these issues.

Reason #1: Dirty Filter

Essential for your washer to begin the spin cycle, water drainage is hampered by a filthy or blocked filter. The washer will stop spinning to prevent harm when they cannot drain correctly.

• Signs of a dirty filter: Water is not draining, and after the cycle garments remain soaked.
• How to fix: Usually found at the bottom front of the washers, find the filter, then clear any trash or accumulation. Before running another load, make sure you replace it firmly.

Reason #2: Faulty Lid Switch

A safety mechanism called the lid switch or door lock prevents the washers from whirling should the door not be tightly closed. Should a lid switch fail, the washer may believe the door is open even when it is not.

• Signs of a faulty lid switch: The washer hums but doesn’t spin, or the washer won’t start the spin cycle at all.
• How to fix: The switch may need to be repaired or replaced if it’s malfunctioning.

Reason #3: Overloaded Washer

Too many items in your washer might throw off the drum, therefore hindering the proper spinning of the machine. Sensors in Samsung washers identify imbalances; when these arise, the machine will either stop spinning completely or lower the spin speed.

• Signs of an overloaded washer: The washer starts to spin but slows down or stops mid-cycle. Clothes may be unevenly wet.
• How to fix: Try redistributing the clothes or removing some items to balance the load, then restart the spin cycle.

Reason #4: Broken Belt

The drum may spin by means of the drive belt, which links the motor to it. If the belt break or wear out, the engine cannot spin the drum.

• Signs of a broken belt: The washer is making a humming noise but not spinning.
• How to fix: Inspect the drive belt for any signs of wear, tears, or looseness. If the belt is damaged, it needs to be replaced.

Reason #5: Broken Motor

If the washer motor fails, the drum won’t spin regardless of load. A faulty motor may also prevent washers from emptying.

• Signs of a broken motor: After checking for other issues, the washer doesn’t spin and the engine doesn’t make any noise.
• How to fix: Professional technicians must fix or replace faulty motors.

How to Repair a Non-Spinning Samsung Washer

Finding out how to repair your Samsung washer after you have determined its reason is the next challenge. These are doable fixes for any typical problem possibly compromising your washer.

Solution 1: Redistributing the Load

If the load be uneven and your washer stop spinning, you will have to reorganize the clothing.

Procedures to correct an imbalanced load:

• Stop the washers and open the door.
• To balance the weight distribution, clear some clothing or divide the burden.
• Restart the spin cycle and tightly close the door.

This helps the drum revolve more smoothly and causes the washers to start spinning normally once again.

Solution 2: Changing a faulty door lock or lid switch.

Another often cited reason Samsung front load washers fail to spin is a broken lid switch or door lock. The washer cannot spin without the door lock mechanism in perfect operating order.

How to replace the door lock?

1. Turn off the washing machines and find the door lock mechanism next to the door frame.
2. Disconnect the wires and take out the screws fastening the lock.
3. Attaching the wire and fastening it with screws, install the new door lock.
4. Revers the washers and see if the issue is fixed.

Solution 3: Replacing the Drive Belt

If the drive belt be broken, you will have to replace it to enable the spinning of the washers once again.

Guidelines for replacing the drive belt:

1. To reach the drum, unplug the washers and flip off the rear panel.
2. Look over the belt for frays and wear. Remove it whether it is broken or loose.
3. Wrapping the new drive belt around the drum pulley and motor pulley helps you install it.
4. Swap the rear panel and test by plugging the washers back in.

Solution 4: Repairing or Replacing the Motor Coupling

The motor coupling connects the motor to the gearbox. Should damage result, your washer could not spin. Changing the motor connection is a rather easy chore.

Methods of replacing the motor coupling:

1. Turn off the washers then slide them to reach the bottom panel.
2. Usually situated between the motor and the gearbox, find the motor coupling.
3. Remove the broken coupler and substitute a new one.
4. Check the washers to guarantee the drum is turning as it should.

Solution 5: Repairing or Replacing the Motor Control Board

The spinning speed and direction of the washer drum are under management by the motor control board. Should this board fail, the washer might spin hardly at all.

How to replace the motor control board?

1. Turn off the washers then find the control board inside the main panel of the machine.
2. Cut the cables running to the malfunctioning board.
3. Connecting the cables in the same arrangement will help you install the new motor control board.
4. Replace the panel and check the spin cycle of the washer.

Conclusion

From a basic uneven load to more major issues like a damaged motor, a Samsung’s washer non-spinning might have a number of reasons. Finding the proper fix depends on knowing the underlying source of the problem. Your Samsung washing machine may be returned in flawless operating condition with correct diagnostics and repairs.

Our specialty at Toronto Appliances Repair is identifying and resolving all kinds of washer issues, including Samsung washers not spinning. Using original Samsung components for long-lasting repairs, our team of qualified experts has the knowledge to promptly and successfully address problems.

Let a broken washer not throw off your everyday schedule. We can assist with any other spinning-related problems, a Samsung front load washer not spinning, or a Samsung top load washers not spinning. With our dependable, same-day service, we can help you recover the efficiency of your washer by means of experienced repair services right now.

REFERENCES

https://www.samsung.com/us/support/troubleshooting/TSG01000997/